Category Archives: Model Design

Matson’s Landing in L-Gauge – A Question of Scale

On the last installment of the Matson’s Landing in L-Gauge series, Mike Pianta asked what scale the locomotive will be if I build it as an 8-wide model. Fortunately, that’s just the topic I had planned to cover in this post.

Generally LEGO® train builders fall into two camps: 6-wide and 8-wide. Traditionally, official LEGO train designs have been built to a “scale” of 6 studs wide. Since the LEGO Group’s trains aren’t really scale models, the width of the design is less important than the playability of the set. Builders wishing to add more realism to their models tend toward the 8-wide “scale” (roughly 1:48) which is a good match to the scale height of a minifig.

For the Matson’s Landing layout, I had originally decided to go with an 8-wide, 1:48 scale. This would allow me to quickly convert real life measurements into studs (real measurement, divided by 1.25, equals number of studs). However, as I began researching logging locomotives to build, I had a realization.

Logging locomotives are really small.

Climax Locomotives
Climax Locomotives

As I wrote in my last post, I’ve settled on building a Climax locomotive. While researching, I found that Climax Manufacturing Company, in their catalog, offered three different models of geared locomotive. The Climax “A” style locomotive is most like the Clishay locomotive that I wrote about before, with an upright or T-style boiler on a basic flat frame. The Climax “B” style is a more traditional looking machine, though the angled side-mounted pistons drive gears beneath the locomotive, instead of directly moving the driving wheels. Their “C” style locomotive is basically a style “B” with an additional tender and more wheels. After reading through the Climax catalog, I really liked the look of the Climax “B”. The gearing is more involved than what I had originally planned, but a challenge while building is always a good thing.

With a definite prototype model picked out, my next step was to research measurements. I took to the Internet in search of articles, photos, and builder’s drawings. I was fortunate to find a mention of scale drawings of a Climax “B” in the February 1985 issue of the magazine Railroad Model Craftsman. I was even more fortunate to find that I had a copy of that issue in my personal magazine collection. I quickly found the issue and read about the Cario & Kanawha Climax No. 5.[1]

(Tip: If a model railroader in his 80s offers to sell you 30 years worth of modeling magazines, especially Model Railroad Craftsman, buy them).

While the article on C&K No. 5 was interesting, what I was really after were the scale line drawings by Ed Gebhart. The basic dimensions shown on the drawings where close to what I had read in the Climax catalog, so I felt fairly certain that any other dimensions would be correct. I scanned the drawings and loaded them into LEGO Model Scaler, an online tool by Paul Kmiec, a.k.a Sariel, of Poland.

LEGO Model Scaler
Prototype drawings in LEGO Model Scaler

LEGO Model Scaler is an awesome tool. Upload an image from the web, draw a known dimension over top of it, enter how many studs that dimension should be, and hit the calculate button. From there on out, any other dimensions you draw over your image will be shown in studs. Incredibly handy for building truly scale models. The other nice thing about the tool is that if you enter your dimensions at a 1:1 scale, you can quickly find dimensions that aren’t listed on the drawings. For instance, on the C&K No. 5 drawing, the narrow gauge track is dimensioned at 3 feet wide. Entering 3 as my base dimension in Scaler, I can quickly see that a Climax “B” locomotive was only 7.5 feet wide. At my target 1:48 scale, this would only be 6 studs wide. While this does fit the scale, it doesn’t leave a lot of room for the PF components (battery box, IR sensor, and motor) needed to run the locomotive.

Climax Rear
Too narrow?

With this in mind, I thought about a few options. I could keep the original scale that I had settled on, and put the PF battery box, and possibly more, in a separate car that would always be attached to the locomotive. Stephen Pakbaz did this very successfully with his Shay Engine. I see the Matson’s Landing layout as a switching layout, however, so I really want the locomotive to be independent of any other cars.

Another option would be to build the locomotive in scale with the track. Climax locomotives were offered in both standard and narrow gauge. Narrow gauge would give me lots of room for electrical components and details, but the model, and therefore the layout, would be huge.

A third option, which I’ve decided to go with, was to base the locomotive scale on the size of the driving wheels. Measuring the standard LEGO train wheel, which I’m planning on using for the drivers, I found them to be about 2.5 studs wide. Looking at the wheel diameter listed in the Climax catalog, I found that the prototype wheels were, on average, 28 to 30 inches. Using these dimensions, and LEGO Model Scaler, I found that I could build my locomotive at roughly 1:33 scale. This should allow me enough space to keep all of the PF parts on board the locomotive, but still be small enough to have a workable layout in the end. Oddly enough, I found that the Climax, at 1:33 scale, turns out to be 8 studs wide. So, while the scale isn’t originally what I had planned, the dimensions are.

In the next post, I’ll go over the start of the locomotive build, and my iterative process for building a (hopefully) functioning model.

[1] Kline, Ben. “The Mystery of Cairo & Kanawha No. 5.” Railroad Model Craftsman, February 1985, 73-76. Drawings by Ed Gebhart.